1.
Refer to the exhibit. Using the network in the exhibit, what would be the default gateway address for host A in the 192.133.219.0 network?
192.135.250.1
192.31.7.1
192.133.219.0
192.133.219.1
2. What two characteristics are commonly associated with dynamic routing protocols? (Choose two.)
require no device configuration
provide routers with up-to-date routing tables
require less processing power than static routes require
consume bandwidth to exchange route information
prevent manual configuration and maintenance of the routing table
3. What are the key factors to consider when grouping hosts into a common network? (Choose three.)
gateways
purpose
physical addressing
software version
geographic location
ownership
4. What statement describes the purpose of a default route?
A host uses a default route to transfer data to another host on the same network segment.
A host uses a default route to forward data to the local switch as the next hop to all destinations.
A host uses a default route to identify the Layer 2 address of an end device on the local network.
A host uses a default route to transfer data to a host outside the local network when no other route to the destination exists.
5. In an IPv4 environment, what information is used by the router to forward data packets from one interface of a router to another?
destination network address
source network address
source MAC address
well known port destination address
6. What type of routing uses information that is manually entered into the routing table?
dynamic
interior
static
standard
7. In a connectionless system, which of the following is correct?
The destination is contacted before a packet is sent.
The destination is not contacted before a packet is sent.
The destination sends an acknowledgement to the source that indicates the packet was received.
The destination sends an acknowledgement to the source that requests the next packet to be sent.
8. What information is added during encapsulation at OSI Layer 3?
source and destination MAC
source and destination application protocol
source and destination port number
source and destination IP address
9. If the default gateway is configured incorrectly on the host, what is the impact on communications?
The host is unable to communicate on the local network.
The host can communicate with other hosts on the local network, but is unable to communicate with hosts on remote networks.
The host can communicate with other hosts on remote networks, but is unable to communicate with hosts on the local network.
There is no impact on communications.
10.
Refer to the exhibit. A network administrator notices that there are too many broadcasts on the network. What two steps can the network administrator take to resolve this problem? (Choose two.)
Replace S2 with a router.
Place all servers on S1.
Disable TCP/IP broadcasts.
Subnet the 192.168.0.0 /24 network.
Disable all unused interfaces on the switches.
11.
Refer to the exhibit. All devices shown in the exhibit have factory default settings. How many broadcast domains are represented in the topology that is shown?
3
4
5
7
8
11
12. What is a component of a routing table entry?
the MAC address of the interface of the router
the destination Layer 4 port number
the destination host address
the next-hop address
13. Which IP packet field will prevent endless loops?
type-of-service
identification
flags
time-to-live
header checksum
14. What is the purpose of a default gateway?
physically connects a computer to a network
provides a permanent address to a computer
identifies the network to which a computer is connected
identifies the logical address of a networked computer and uniquely identifies it to the rest of the network
identifies the device that allows local network computers to communicate with devices on other networks
15. Which intermediary devices could be used to implement security between networks? (Choose two.)
router
hub
switch
firewall
access point
bridge
16.
Refer to the exhibit. The network in the exhibit is fully operational. What two statements correctly describe the routing for the topology that is shown? (Choose two.)
192.168.0.2 is the next-hop address that is used by R3 to route a packet from the 10.0.0.0 network to the 172.16.0.0 network.
10.0.0.1 is the next-hop address that is used by R1 to route a packet from the 192.168.12.0 network to the 10.0.0.0 network.
192.168.0.1 is the next-hop address that is used by R1 to route a packet from the 192.168.12.0 network to the 172.16.0.0 network.
172.16.0.1 is the next-hop address that is used by R3 to route a packet from the 10.0.0.0 to the 172.16.0.0 network.
192.168.0.1 is the next-hop address that is used by R2 to route a packet from the 172.16.0.0 network to the 192.168.12.0 network.
192.168.0.2 is the next-hop address that is used by R2 to route a packet from the 172.16.0.0 network to the 192.168.12.0 network.
17.
Refer to the exhibit. A network administrator is troubleshooting a connectivity problem and needs to determine the address that is used to forward network packets out the network. Using the netstat -r command, the administrator would identify which address as the address to which all hosts send packets that are destined for an outside network?
10.10.10.26
127.0.0.1
10.10.10.6
10.10.10.1
224.0.0.0
18. Which portion of the network layer address does a router use to forward packets?
host portion
broadcast address
network portion
gateway address
19. When the destination network is not listed in the routing table of a Cisco router, what are two possible actions that the router might take? (Choose two.)
The router sends an ARP request to determine the required next hop address.
The router discards the packet.
The router forwards the packet toward the next hop indicated in the ARP table.
The router forwards the packet to the interface indicated by the source address.
The router forwards the packet out the interface indicated by the default route entry.
20. Which three statements are true about routes and their use? (Choose three.)
If no route to the destination network is found, the packet is returned to the previous router.
If the destination network is directly connected, the router forwards the packet to the destination host.
If multiple network entries exist for the destination network, the most general route is used to forward the packet.
If no route exists for the destination network and a default route is present, the packet is forwarded to the next-hop router.
If the originating host has a default gateway configured, the packet for a remote network can be forwarded using that route.
If a host does not have a route manually configured for the destination network, the host will drop the packet.
21. What are three common problems with a large network? (Choose three.)
too few broadcasts
performance degradation
security issues
limited management responsibility
host identification
protocol compatibility
Tags: which IP packet field will prevent endless loops?, Refer to the exhibit All devices shown in the exhibit have factory default settings How many broadcast domains are represented in the topology that is shown?, If the default gateway is configured incorrectly on the host what is the impact on communications?, ccna exploration 1 chapter 5 answers, What statement describes the purpose of a default route?, Which intermediary devices could be used to implement security between networks? (Choose two ), CCNA EXPLORATION 1 CHAPTER 5, What information is added during encapsulation at OSI Layer 3?, CCNA Exploration 1 Chapter 5 Exam, Refer to the exhibit Using the network in the exhibit what would be the default gateway address for host A in the 192 133 219 0 network?, exploration 1 chapter 5, which ip packet field will prevent endless loops ccna, When the destination network is not listed in the routing table of a Cisco router what are two possible actions that the router might take? (Choose two ), What is a component of a routing table entry?, cisco 1 chapter 5 answers, Refer to the exhibit The network in the exhibit is fully operational What two statements correctly describe the routing for the topology that is shown? (Choose two ), Refer to the exhibit A network administrator notices that there are too many broadcasts on the network What two steps can the network administrator take to resolve this problem? (Choose two ), ccna chapter 5 practice test, What is a component of a routing table entry, CCNA 1 Chapter 5 Practice Test Questions, Refer to the exhibit All devices shown in the exhibit have factory default settings How many broadcast domains are represented in the topology that is shown, Which portion of the network layer address does a router use to forward packets?, Which intermediary devices could be used to implement security between networks?, ccna 1 exploration chapter 5 answers, In a connectionless system which of the following is correct?, Which addresses are added during encapsulation at the network layer? Choose all that apply, When the destination network is not, Which device forwards data by using the Layer 2 destination address?, If the default gateway is configured incorrectly on the host what is the impact on communications, What is the purpose of a default gateway?, Which portion of the network layer address does a router use to forward packets, cisco exploration 1 chapter 5, When the destination network is not listed in the routing table of a Cisco router what are two possible actions that the router might take?, cisco exploration 1 chapter 5 answers, Which intermediary devices could be used to implement security between networks? (Choose two ) router, ccna exploration 4 chapter 5 osi network layer answers, which intermediary devices could be used to implement security between networks choose two, Which IP packet field will prevent endless loops? type-of-service identification flags time-to-live header checksum, in a connectionless system which of the following is correct, ccna discovery 1 exams chapter 5, can devices on same network communicate with no default gateway, Refer to the exhibit Using the network in the exhibit what would be the default gateway address for host A in the 192 133 219 0 network, which ip packet field, Which three statements are true about routes and their use, ccna exploration chapter 5 correct answer, What type of routing uses information that is manually entered into the routing table?, Refer to the exhibit A network administrator notices that there are too many broadcasts on the network What two steps can the network administrator take to resolve this problem, default gateway ccna, exploration1 chapter5, how many broadcast domains exam ccna 100% 1009998979695949392919089888786851234567890 ABCEFGHIJKLMNOPQRSTUVWXYZ latest update .pdf .doc extension answer sheets sheet compelete perfect prfect online exam answers free download accurate january february march april may june july august september october november december updated updates 2011 2012 2013 2014 2015 2016 2017 2018 2000 2k score top new passing passed
No comments:
Post a Comment