1.
Refer to the exhibit. What three statements are true about the IP configuration that is shown? (Choose three.)
The address that is assigned to the computer represents private addressing.
The computer is unable to communicate outside of the local network.
The network of this computer can have 126 hosts.
The prefix of the computer address is /27.
The IP address that is assigned to the computer is routable on the Internet.
The IP address that is assigned to the computer is a broadcast address.
2. As network administrator, what is the subnet mask that allows 510 hosts given the IP address 172.30.0.0?
255.255.0.0
255.255.248.0
255.255.252.0
255.255.254.0
255.255.255.0
255.255.255.128
3. Which OSI layers offers reliable, connection-oriented data communication services?
application
presentation
session
transport
network
4. Which type of media is immune to EMI and RFI? (Choose two.)
10 Base-T
10 Base-2
10 Base-5
100 Base-FX
100 Base TX
1000 Base LX
5. When connectionless protocols are implemented at the lower layers of the OSI model, what is usually used to acknowledge that the data was received and to request the retransmission of missing data?
IP
UDP
Ethernet
a connectionless acknowledgement
an upper-layer, connection-oriented protocol or service
6. Which combination of network id and subnet mask correctly identifies all IP addresses from 172.16.128.0 through 172.16.159.255?
172.16.128.0 255.255.255.224
172.16.128.0 255.255.0.0
172.16.128.0 255.255.192.0
172.16.128.0 255.255.224.0
172.16.128.0 255.255.255.192
7. During the encapsulation process, which identifiers are added at the transport layer?
two networks routing the packets
two applications communicating the data
two hosts at either end of the communication
two nodes on the local network exchanging the frame
8. What are three characteristics of CSMA/CD? (Choose three)
Devices can be configured with a higher transmission priority.
A jam signal indicates that the collision has cleared and the media is not busy.
A device listens and waits until the media is not busy before transmitting.
The device with the electronic token is the only one that can transmit after a collision.
All of the devices on a segment see data that passes on the network medium.
After detecting a collision, hosts can attempt to resume transmission after a random time delay has expired.
9.
Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the different devices?
Connection 1 – rollover cable
Connection 2 – straight-through cable
Connection 3 – crossover cable
Connection 1 – crossover cable
Connection 2 – rollover cable
Connection 3 – crossover cable
Connection 1 – straight-through cable
Connection 2 – crossover cable
Connection 3 – crossover cable
Connection 1 – straight-through cable
Connection 2 – crossover cable
Connection 3 – straight-through cable
Connection 1 – crossover cable
Connection 2 – straight-through cable
Connection 3 – crossover cable
10.
Refer to the exhibit. A network technician is trying to determine the correct IP address configuration for Host A. What is a valid configuration for Host A?
IP address: 192.168.100.19; Subnet Mask: 255.255.255.248; Default Gateway: 192.16.1.2
IP address: 192.168.100.20; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.17
IP address: 192.168.100.21; Subnet Mask: 255.255.255.248; Default Gateway: 192.168.100.18
IP address: 192.168.100.22; Subnet Mask: 255.255.255.240; Default Gateway: 10.1.1.5
IP address: 192.168.100.30; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.1.1
IP address: 192.168.100.31; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.18
11.
Refer to the exhibit. Host A is transmitting data to host B. What addresses will host A use to for the destination IP and MAC addresses in this communication?
Destination MAC: BBBB:BBBB:BBBB Destination IP: 172.22.0.62
Destination MAC: DDDD:DDDD:DDDD Destination IP: 172.22.0.75
Destination MAC: EEEE:EEEE:EEEE Destination IP: 172.22.0.62
Destination MAC: BBBB:BBBB:BBBB Destination IP: 172.22.0.75
Destination MAC: EEEE:EEEE:EEEE Destination IP: 172.22.0.75
Destination MAC: DDDD:DDDD:DDDD Destination IP: 172.22.0.94
12.
Refer to the exhibit. Assume all devices are using default configurations. How many subnets are required to address the topology that is shown?
1
3
4
5
7
13.
Refer to the exhibit. Which two statements describe the information that is represented in the header? (Choose two)
This is a server response.
The UDP protocol is being used.
The destination port indicates a Telnet session.
The return segment will contain a source port of 23.
The next session originated from the client of this session will use the source port number 13358.
14.
Refer to the exhibit. The command that is shown was issued on a PC. What does the IP address 192.168.33.2 represent?
IP address of the host
default gateway of the host
IP address of the homepage for the host
primary domain name server for the host
IP address of the website resolver1.mooki.local
15.
Refer to the exhibit. A router, whose table is shown, receives a packet that is destined for 192.168.1.4. How will router treat the packet?
The packet will be dropped.
The packet will be forwarded via FastEthernet 0/0.
The packet will be forwarded to the destination host.
The packet will be forwarded to the 192.168.1.3 next-hop address.
16.
Refer to the exhibit. A network administrator remotely accesses the CLI of RouterB from PC1 using Telnet. Which statement is true about this connection?
The data is automatically encrypted.
A Telnet server process is running on PC1.
The connection is made through a VTY session on the router.
A GET request was sent to RouterB to retrieve data during this session.
17. Which three IPv4 addresses represent a broadcast for a subnet? (Choose three.)
172.16.4.63 /26
172.16.4.129 /26
172.16.4.191 /26
172.16.4.51 /27
172.16.4.95 /27
172.16.4.221 /27
18.
Refer to the exhibit. What is required on host A for a network technician to create the initial configuration on Router1?
an FTP client
a Telnet client
a terminal emulation program
a web browser
19. Which three statements characterize the transport layer protocols? (Choose three.)
TCP and UDP port numbers are used by application layer protocols.
TCP uses port numbers to provide reliable transportation of IP packets.
UDP uses windowing and acknowledgments for reliable transfer of data.
TCP uses windowing and sequencing to provide reliable transfer of data.
TCP is a connection-oriented protocol. UDP is a connectionless protocol.
20. The Layer 4 header contains which type of information to aid in the delivery of data?
service port number
host logical address
device physical address
virtual connection identifier
21.
Refer to the exhibit. The tracert command is initiated from PC1 to PC4. Which device will send a response to the initial tracert packet from PC1?
Athens
Ankara
London
Paris
PC4
22.
Refer to the exhibit. Host A attempts to establish a TCP/IP session with host C. During this attempt, a frame was captured with the source MAC address 0050.7320.D632 and the destination MAC address 0030.8517.44C4. The packet inside the captured frame has an IP source address 192.168.7.5, and the destination IP address is 192.168.219.24. At which point in the network was this packet captured?
leaving host A
leaving ATL
leaving Dallas
leaving NYC
23
Refer to the exhibit. Which set of devices contains only intermediary devices?
A, B, D, G
A, B, E, F
C, D, G, I
G, H, I, J
24
Refer to the exhibit. What two facts can be determined from the information that is given? (Choose two.)
This exchange is part of the three-way handshake.
The source port indicates that a Telnet session has been initiated.
The data is flowing from server to client.
The destination port indicates that an HTTP session has been initiated.
The data listed is associated with the transport layer.
The source port does not support communication with the destination port that is listed.
25. Due to a security violation, the router passwords must be changed. What information can be learned from the following configuration entries? (Choose two)
Router(config)# line vty 0 3
Router(config-line)# password c13c0
Router(config-line)# login
The entries specify three Telnet lines for remote access.
The entries specify four Telnet lines for remote access.
The entries set the console and Telnet password to “c13c0″.
Telnet access will be denied because the Telnet configuration is incomplete.
Access will be permitted for Telnet using “c13c0″ as the password.
26.
Refer to the exhibit. Cable 1 and cable 2 have the ends wired for specific physical layer requirements. The table lists each segment by number and the cable which has been installed by the network technician between the network components on that segment. From the data given, which segments have the correct cable installed? (Choose three.)
segment1
segment2
segment3
segment4
segment5
27. Which password is automatically encrypted when it is created?
vty
aux
console
enable secret
enable password
28.
Refer to the exhibit. Which logical topology best describes the exhibited network?
star
ring
point-to-point
multiaccess
mesh
29.
Refer to the exhibit. The network containing router B is experiencing problems. A network associate has isolated the issue in this network to router B. What action can be preformed to correct the network issue?
issue the clock rate command on interface Serial 0/0/0
issue the description command on interface Serial 0/0/1
issue the ip address command on interface FastEthernet 0/0
issue the no shutdown command on interface FastEthernet 0/1
30. What are two characteristics of the data link layer? (Choose two.)
It segments and reorders the data.
It exchanges the frames between nodes.
It defines the method by which network devices place data onto the media.
It manages the transfer of data between the processes that run on each host.
It retrieves signals from the media and restores them to their bit representations.
31. Which of the following are the address ranges of the private IP addresses? (Choose three.)
10.0.0.0 to 10.255.255.255
200.100.50.0 to 200.100.25.255
150.150.0.0 to 150.150.255.255
172.16.0.0 to 172.31.255.255
192.168.0.0 to 192.168.255.255
127.16.0.0 to 127.31.255.255
32.
Refer to the exhibit. The diagram represents the process of sending email between clients. Select the list below that correctly identifies the component or protocol used at each numbered stage of the diagram.
1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA
1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA
1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA
1.MDA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MUA 7.POP 8.MDA
1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA
33.
Refer to the exhibit. On the basis of the IP configuration that is shown, what is the reason that Host A and Host B are unable to communicate outside the local network?
Host A was assigned a network address.
Host B was assigned a multicast address.
Host A and Host B belong to different networks.
The gateway address was assigned a broadcast address.
34.
Refer to the exhibit. What is the correct destination socket number for a web page request from Host A to the web server?
00-08-a3-b6-ce-46
198.133.219.25:80
http://www.cisco.com
C 198.133.219.0/24 is directly connected, FastEthernet0/0
35. A routing issue has occurred in you internetwork. Which of the following type of devices should be examined to isolate this error?
access point
host
hub
router
switch
36. Which OSI layer does IP rely on to determine whether packets have been lost and to request retransmission?
application
presentation
session
transport
37. Which range of port numbers are reserved for services that are commonly used by applications that run on servers?
0 to 255
0 to 1023
1024 to 49151
49152 to 65535
38.
Examine the graphic with current configurations. Host A in the Clerical offices failed and was replaced. Although a ping to 127.0.0.1 was successful, the replacement computer can not access the company network. What is the likely cause of the problem?
IP address incorrectly entered
network cables unplugged
subnet mask incorrectly entered
network card failure
39.
Refer to the exhibit. When computer A sends a frame to computer D, what computers receive the frame?
only computer D
only computer A and computer D
only computer B, computer C, and computer D
all computers
40. In a Cisco IOS device, where is the startup-configuration file stored?
Flash
NVRAM
RAM
ROM
41.
Refer to the exhibit. With the router running NAT, what IP addresses can be applied to the computer to allow access to the Internet? (Choose three)
192.168.18.38
192.168.18.48
192.168.18.49
192.168.18.52
192.168.18.59
192.168.18.63
42. A technician is asked to secure the privileged EXEC mode of a switch by requiring a password. Which type of password would require this login and be considered the most secure?
console
enable
enable secret
VTY
43. Which prompt represents the appropriate mode used for the copy running-config startup-config command ?
Switch-6J>
Switch-6J#
Switch-6J(config)#
Switch-6J(config-if)#
Switch-6J(config-line)#
44.
Refer to the exhibit. A technician is working on a network problem that requires verification of the router LAN interface. What address should be pinged from this host to confirm that the router interface is operational?
127.0.0.1
192.168.64.196
192.168.254.1
192.168.254.9
192.168.254.254
45. What is true regarding network layer addressing? (Choose three)
uses a flat structure
prevent broadcasts
heirarchical
uniquely identifies each host
48 bits in length
contains a network portion
46.
Refer to the exhibit. What function does router RT_A need to provide to allow Internet access for hosts in this network?
address translation
DHCP services
ftpd
web server
47. A PC can not connect to any remote websites, ping its default gateway, or ping a printer that is functioning properly on the local network segment. Which action will verify that the TCP/IP stack is functioning correctly on this PC?
Use the ipconfig /all command at the host’s command prompt.
Use the ping 127.0.0.1 command at the command prompt.
Use the traceroute command at the command prompt to identify any failures on the path to the gateway.
Use FTP to check for connectivity to remote sites.
Download a troubleshooting tool from the PC manufacturer’s website.
48.
Refer to the exhibit. What two facts can be determined about the exhibited topology? (Choose two)
A single broadcast domain is present
Two logical address ranges are required.
Three broadcast domains are shown.
Four networks are needed.
Five collision domains exist.
49. Which two functions of the OSI model occur at layer two? (Choose two.)
physical addressing
encoding
routing
cabling
media access control
50. When must a router serial interface be configured with the clock rate command?
when the interface is functioning as a DTE device
when the interface timers have been cleared
when the connected DTE device is shut down
when the interface is functioning as a DCE device
Tags: To which range of port numbers would the port number for POP3 belong?, Which password is automatically encrypted when it is created?, Refer to the exhibit Which IP address and subnet mask can be configured on host H1 if it is to communicate with the network?, A technician is asked to secure the privileged EXEC mode of a switch by requiring a password Which type of password would require this login and be considered the most secure?, ccna exploration 1 final exam answers, Which password is automatically encrypted when it is created, Which range of port numbers are reserved for services that are commonly used by applications that run on servers?, When connectionless protocols are implemented at the lower layers of the OSI model what is usually used to acknowledge that the data was received and to request the retransmission of missing data?, Which of the following are the address ranges of the private IP addresses? (Choose three ), which password is automatically encrypted when it is created answers, A routing issue has occurred in your internetwork Which of the following type of devices should be examined to isolate this error?, Refer to the exhibit The command that is shown was issued on a PC What does the IP address 192 168 33 2 represent?, Which range of port numbers are reserved for services that are commonly used by applications that run on servers, cisco exploration 1 final exam answers, Refer to the exhibit Host A attempts to establish a TCP/IP session with host C During this attempt a frame was captured with the source MAC address 0050 7320 D632 and the destination MAC address 0030 8517 44C4 The packet inside the captured frame has an I, What are two characteristics of the data link layer? (Choose two ), exploration 1 final exam, What are two characteristics of the data link layer, Refer to the exhibit The network containing router B is experiencing problems A network associate has isolated the issue in this network to router B What action can be preformed to correct the network issue?, A technician is asked to secure the privileged EXEC mode of a switch by requiring a password Which type of password would require this login and be considered the most secure, Which password is automatically encrypted when it is created? vty, ccna exploration final exam set 1, a routing issue has occurred in your internetwork, The Layer 4 header contains which type of information to aid in the delivery of data?, Exploration 1 Final, data transmission media exam question, What are three characteristics of CSMA/CD? (Choose three ), What are two characteristics of the data link layer? (Choose two ) It segments and reorders the data It exchanges the frames between nodes It defines the method by which network devices place data onto the media It manages the transfer of data between the, FINAL EXAM ANSWER, Which of the following are the address ranges of the private IP addresses?, Refer to the exhibit What function does router RT_A need to provide to allow Internet access for hosts in this network?, 01 When connectionless protocols are implemented at the lower layers of the OSI model what is usually used to acknowledge that the data was received and to request the retransmission of missing data?, ccna discovery 1 final examen and answer 2011, port numbers would the port number for POP3 belong, a technician is asked to secure, When connectionless protocols are implemented at the lower layers of the OSI model what is usually used to acknowledge that the data was received and to request the retransmission of missing data, What information is used at each hop to determine where the packet will be forwarded next, Refer to the exhibit Which two facts can be determined about the topology?, ccna exploration 1 final online exam answers, During the encapsulation process what identifiers are added at the transport layer?, CCNA 1 final examination answer, the diagram represents the process of sending email, ccna 1 2011 final exam answer, Refer to the exhibit Which logical topology best describes the exhibited network?, Refer to the exhibit What is required on host A for a network technician to create the initial configuration on Router1?, ccna exploration 1 final exam with answer, What are two characteristics of the data link layer?, What are three characteristics of CSMA/CD? (Choose three ) Devices can be configured with a higher transmission priority A jam signal indicates that the collision has cleared and the media is not busy A device listens and waits until the media is not busy, Host A attempts to establish a TCP/IP session with host C During this attempt a frame was captured with the source MAC address 0050, it defines the method by which network devices place data onto the media 100% 1009998979695949392919089888786851234567890 ABCEFGHIJKLMNOPQRSTUVWXYZ latest update .pdf .doc extension answer sheets sheet compelete perfect prfect online exam answers free download accurate january february march april may june july august september october november december updated updates 2011 2012 2013 2014 2015 2016 2017 2018 2000 2k score top new passing passed quiz quizzes online complete course course certified certificate
hi this material is still good?
ReplyDelete